WizCG grinder
WizCG grinder WizCG grinder WizCG grinder WizCG grinder

WizCG grinder

SKU: 20030

$189.95 $209.95

Order this glass grinder machine today and receive FREE UPS Ground Shipping anywhere in the lower 48 U.S. states!

The WizCG is our best-seller because of its power and value. The workhorse 30 oz-in torque motor offers plenty of power to do the jobs you want. Use this American-made machine for grinding and shaping glass edges, doing stained glass work and drilling holes in glass. The WizCG comes with TWO different sized grinding bits to accommodate your edge-grinding needs, which is a great value! You can use both grinding bits at once, eliminating removing/replacing different sized grinding bits! The WizCG is a great choice for hobbyists who require quality.

Setup is easy. Simply install the two included diamond grinding bits, wet the coolant sponges with clean water and turn it on with the two-way power switch.

Important purchasing note

This is a 115 volt machine and is ONLY suitable for use in the U.S., Canada, Mexico and Japan.

Non-U.S. customers

We are not responsible for any import duties or customs charges. Any such fees incurred to receive your package are not covered by us. Please consult your country's customs policy for more information.

  • Powerful 30 oz-in torque, 115V motor provides all the power you need to get the job done
  • Machine housing is lightweight, rustproof and impact resistant, making it easy to travel with and very portable
  • Use TWO different sized grinding bits at the same time
  • Large 10-1/2" X 8-1/2" work surface is reversible and provides enough room for larger projects
  • Lift-off reservoir can be easily removed for fast and easy cleaning
  • Accepts (but doesn't include) Inland Craft's wire frame face shield support for use with our FaceShield or MagnaShield accessories
Optional accessories
  • SecondStory work surface - Elevated work surface that makes it easier to grind and drill holes when using small diameter drilling heads or a stacked bit set up
  • FaceShield - Large, 10" X 8-3/4" acrylic face shield provides added protection from grinding and sawing debris
  • MagnaShield - Large, 10" X 8-3/4" face shield has a built-in optical quality convex magnifying surface making it easier to see your work, reduces eye strain and provides additional protection against grinding and sawing debris

Machine specifications

  • Machine dimensions: 12" L X 10" W X 7" H
  • Machine weight: 6-1/2 lbs
  • Grinder housing construction: injection-molded plastic
  • Work surface: 10-1/2" L X 8-1/2" W open grid surface

Motor specifications

  • Voltage: 115V (U.S. plug)
  • RPM/UPM (idle): 3,500
  • Maximum torque: 30 oz-in
  • Frequency: 60Hz
  • Running current: <1A
  • Maximum horse power: 1/11 hp
  • Watts in: 215
  • Watts out (at peak torque): 55
  • Motor shaft outer diameter: 0.312" (5/16") stainless steel

Customer Reviews

Based on 63 reviews
86%
(54)
11%
(7)
2%
(1)
2%
(1)
0%
(0)
J
James Cameron
Could be better

Replaced my old Glastar grinder with the WizCG. Don’t like the water tray much. Your ads say it’s convenient to just remove it to dump it out and clean it, but it really isn’t, since you have to remove the grinding bit(s) each time, note their position, and replace them. The water tray is hard to scrape out, since you have left all sorts of mold flashing inside. I’ve had to shave these off with a sharp chisel so I could scrape it out. You mention caution about getting water down the motor shaft, which kind if implies that there isn’t a proper seal on the motor shaft.. if so, that’s a weak design feature. Finally, the “bitsert” gets pushed back when the sponge is in place, raising the front edge so that any piece of glass you’re grinding hits it and sticks. I’ve had to add some small stainless machine screws to hold the front edge if that down and out of the way.
The grinding bits (drums) seem to be good quality, and are holding up well. Too bad you don’t have the 1/4” bit thread into the shaft so one could remove the larger one without taking the smaller one off.
Overall, it’s a pretty nice grinder, but has several annoying design features that make it not as good as my old Glastar.

S
SANDRA NEVEAU
WizCG grinder

I love the WizCG grinder. I do find it a bit strange that you have to take the grinding wheel off every time you have to clean it. But other than that it is easy to clean. I hope it lasts as long as my first Inland grinder.

B
Brooke Jackson
Great product

It arrived very quickly, great packaging, and works great.

S
Shellie Mull

WizCG grinder

R
Raymond Dennis
New grinder

Just got to use my new grinder today. Love everything about it. My only issue with it is I wish the grid table was a little stiffer plastic. It seems to have a little flex. I think I can fix this problem with a little shim under the table.

123

You may also like